What’s been going on with AD7MI?

It’s been a busy summer so far.

– Memorial Day: I really enjoyed the special event station operation – W4M. I operated from Fort Monroe on Saturday and Sunday from a WWII coastal artillery battery overlooking the Chesapeake, wonderful weather and some great contacts. I setup a G5RV for the antenna and used a portable generator for power.

– The Smithsonian, NN3SI: During my trip to Washington DC, I had the opportunity to be a guest operator at the Smithsonian’s own amateur radio station, located at the Museum of American History.

– Lighthouse Activations: Enjoyed a relaxing few days down in the Outer Banks, NC and was able to activate the Bodie Island Lighthouse (USA-067) and the Currituck Beach Lighthouse (USA-212). Link here to the Outer Banks Repeater Association: http://obra.aginet.com/


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
From : W2EHD
To : ad7mi
Subject : Re: 442.850

Scott – It was a pleasure to meet you – if only on the air.
Re: the the UHF side of the mobile radio. Might consider selecting medium or low power when running mobile – especially when the repeater of choice is not far away.

I am sending along a URL for a tape measure beam. Originally, I think the author meant to use it in DFing – Direction-finding – competitions – but despite the fact that it’s rather ugly and makes lots of noise when the wind blows the elements – it seems the ideal solution for accessing a repeater from a remote (vacation) location.
I bought an el cheapo grande 25 ft. tape measure a few years ago, and 8 bucks worth of the PVC tubing he recommends.
There are several of these antennae in my workshop. One thing I did was to cast a couple of concrete bases – using galvanized pails that I bought at ACE.
One 60-odd bag of Sak-Crete will let you make a couple of bases. Glue some scrap carpeting to the bottom and you’ve got built-on floor protection.

As presently described, the tape measure antenna is only good on 2 meters. The author mentions that it may well be possible to change the element dimensions and spacing to put it into the UHF portion of the spectrum. I may try one out on 70 cm, with a watt meter in the line, just for grins.
Keep in touch.
If you wish, I will add your address to the OBRA email list, which will keep you informed about major doings around here. You would not get a lot of mail from OBRA, believe me.
73,
Jack
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Next project: I’m working on a portable HF/VHF/UHF system. Intent is to build a complete setup (rig, power supply, tuner, SWR meter, NOMIC RigBlaster, etc.) into an easily transportable box.

Busy day…..

(1) Complete support pole for G5RV feed point….
– this is complete except for the guy-wire. I need to get guy-wire for the upper 1/3 and lower 1/3 of the mast. I think the mast is going to work out well. It is composed of two painter’s poles (Mr. Long Arm). Each has a maximum length of 23′. For the upper section, I cut away the handle on the bottom. This will allow me to nest the upper portion’s lower 1/3 into the bottom portion’s top 1/3 of the pole. I think the total height of the mast will be around 38′. Also drilled a hole in the very top of the upper section and put an eye-bolt through it. Attached to the eye-bolt is a d-ring. I will attach the top of the feed point for the G5RV to the d-ring. As long as I can get some guy-wire… I’ll be good to go.

(2) Prep supports for the G5RV ends….
– got two large buckets from Home Depot. I placed a 3″ piece of PVC pipe (length just over the lip of the bucket) vertically in the center of the bucket. Around the pipe I put in about 4″ of cement. Turned about pretty good. I’ll be able to slide in a 2 1/2″ PVC pipe (10′ long) into the bucket and use it to secure the ends of the G5RV.

(3) Get a pop-up shelter for the operations table….
– got it at Target. 10′ by 10′ with a mosquito net. It will probably due okay in light rain, but not much more.

… and that was it for the list.

I did set up the FT-817 outside with my new RigBlaster NOMIC. Worked pretty good, got an PSK31 contact on 20M from Iowa with 5 watts. Have not set up the Tokyo amp yet.